Mold Remediation in San Diego

Mold in a house is almost never the real problem. It’s the evidence. Mold spores float in every home, and they stay harmless until they land on something that stays wet. Find the water, stop it and dry the area, and the mold has nothing to live on. Skip that step, and no amount of scrubbing or spraying will keep it from coming back. The EPA puts it in one line: the key to mold control is moisture control. That’s why our mold remediation work in San Diego starts with plumbing, the trade we’ve practiced since 2007.

Step One Is the Leak

Most mold we’re called about sits next to a water source. Think of a supply line weeping inside a wall, a drain joint under a bathroom, a slow leak behind a refrigerator, or a shower valve leaking into the framing. Before anything gets cleaned, we find that source and repair it. Sometimes it’s not where the stain suggests. On one job, a garage ceiling had to be opened to trace a leak back to an upstairs shower valve that needed an unusual replacement part. On another, in a 31-year-old two-story house, we opened a wall to replace a leaking drain pipe from the upstairs bathroom. In both cases the wet area could only be dealt with once the water stopped.

If you’re not sure where the moisture is coming from, our moisture detection readings map how far it has spread. If you want mold confirmed or sampled before work starts, see mold inspection.

Small Patch or Real Remediation?

Size matters more than color. EPA’s homeowner guide says a moldy area under about 10 square feet, roughly a 3 by 3 foot patch, is usually a job you can handle yourself. Scrub hard surfaces with detergent and water, dry them completely, and wear gloves, goggles and an N-95 respirator. The same guide says to bring in a professional when:

  • Mold covers more than about 10 square feet, or there was a lot of water damage.
  • The water came from sewage or another contaminated source.
  • Mold is likely hidden behind drywall, under flooring or inside the HVAC system. Don’t run a system you suspect is contaminated, since it can spread mold through the house.
  • Someone in the home has health concerns. Talk with a health professional before cleanup starts.

Two things not to do, from the same guide: don’t paint or caulk over mold, because the paint will peel and the mold stays. And bleach isn’t recommended as a routine cleanup step; dead mold can still cause allergic reactions, so it has to be removed, not just killed.

How the Work Scales

For jobs bigger than a small patch, EPA’s remediation guide sets the setup by the size of the area. We follow the same logic:

Moldy area

Containment

What that looks like

Under about 10 sq ft

Usually none beyond care and protective gear

Clean, dry, bag and discard what can’t be cleaned

About 10 to 100 sq ft

Limited containment

A single layer of 6-mil fire-retardant plastic sheeting around the area, a slit entry, and negative air pressure so spores stay inside

Over 100 sq ft

Full containment

Double layers of sheeting and negative pressure exhausted outdoors

Inside the containment, porous materials that have grown mold, such as drywall, insulation, carpet and pad, usually come out, because mold fills their pores and can’t be fully cleaned. Hard surfaces like framing and tile are cleaned and dried. HEPA vacuums and air scrubbers capture loose spores. Then the area is dried with fans and dehumidifiers, and moisture readings tell us when it’s actually dry. Our structural drying page covers that stage. Even on plumbing repairs, we cover surfaces with plastic sheeting before we open anything, so dust and debris stay where they belong.

Do You Need a Mold Test?

Usually not when mold is visible. The EPA says sampling is generally unnecessary in that case, and there are no federal limits that a result could be measured against. Sampling earns its keep in other situations: when a musty smell has no visible source, or after cleanup to show an area was adequately cleaned. Either way, it should be done by someone experienced in sampling and interpreting the results.

When Is It Finished?

EPA’s checklist is simple and worth holding any contractor to. The water or moisture problem is completely fixed. Visible mold and moldy odors are gone, though staining may remain. A return visit shortly after shows no new water damage or growth. And people can use the space again without health complaints. Rebuilding walls and floors should wait until all four are true.

Keeping It From Coming Back

Dry water damage within 24 to 48 hours, and in most cases mold won’t grow. Our guide to preventing mold after water damage goes through that window material by material. Keep indoor humidity below 60 percent, ideally 30 to 50. Run the bathroom fan during and after showers, keep the air conditioner’s drip pan and drain line clear, and insulate cold water pipes that sweat. Any drip under a sink or behind an appliance is worth fixing the week you find it. If you’re not sure where hidden water is coming from, our leak detection team can track it down.

For mold you’ve found or suspect, call (858) 567-0544 during weekday office hours, 8 AM to 5 PM, and mention any leak or water event you know about. Photos sent through Contact Us help us plan the visit. Our contractor license is CSLB #910268. Tony Misleh, the master plumber behind the company, opened it in 2007 and still leads it.

Contact Us

    For Same-Day
    Water Heater Service,
    Call Us On

    (858) 567-0544

    Check Out Our Ratings!