Fiberglass Tub Installation in San Diego: Make Sure It's the Tub That Failed
- Home
- /
- Fiberglass Tub Installation in San Diego
Fiberglass tubs are light, affordable and still the standard fit for a three-wall alcove, so plenty of San Diego bathrooms have one. When water shows up where it shouldn’t, though, the tub itself isn’t always the part that failed. Before you pay to pull a tub out, it helps to know which problems need a new one and which need a few hours of work on the drain. Courtesy Plumbing replaces fiberglass tubs and repairs their drains and fittings on weekdays from 8 AM to 5 PM. A tub that simply drains slowly is a clog, and Drain Mob, the partner we trust with drain work, clears those.
Tub Problem or Drain Problem?
Every tub has a drain assembly plumbers call the waste and overflow. It’s the drain in the floor of the tub, the overflow opening under the spout, and the pipes and gaskets behind the wall that join them to the house drain. A lot of leaks blamed on the tub come from there.
What you notice | Usually means | Typical fix |
A stain on the ceiling below the bathroom | A worn gasket or loose joint at the drain or overflow | Replace the waste and overflow; the tub can stay |
Water dripping from behind the spout | A worn spout or a failed seal where it meets the wall | Replace the spout |
Overflow cover screws rusted solid | Corroded overflow hardware | Replace the overflow parts |
Fine cracks or crazing in the finish, no leak | Wear in the gel coat surface | Refinish, or live with it |
A crack through the tub floor, or a floor that flexes underfoot | Broken shell or failed support beneath it | Replace the tub and repair what’s under it |
Our customers’ reviews mention all of these smaller fixes. One had a waste and overflow replaced after water reached the ceiling below, another a spout that leaked out of the back, and a third an overflow cover whose screw had rusted in place. None of those needed a new tub. On the other hand, a cracked floor or a spongy feel when you step in means the tub is no longer supported, and patching the crack won’t fix that.
Choosing a Replacement That Fits
Alcove tubs are most commonly 60 inches long, but width, height and the drain side all vary, so measure the opening and note the drain end before you shop. Standing in the tub and facing the faucet, a drain on your left is a left-hand tub. Buy the wrong hand and the drain won’t line up with the pipe below the floor. Also measure the doorway and hallway. A tub alone usually fits through, but a one-piece tub and shower unit often won’t fit through the door of a finished house.
Check the label as well. Plastic tubs, fiberglass and acrylic included, are tested to the IAPMO Z124 and CSA B45.5 standards, and a certified tub will say so on its label or spec sheet.
Support Is What Makes a Fiberglass Tub Last
A fiberglass shell flexes. Set it on an uneven or soft subfloor and it moves every time someone steps in, which cracks the shell over time and breaks the caulk line at the wall. Manufacturers are specific about this. Kohler’s installation guide for one of its Sterling baths says the bath must be level and fully supported by the subfloor, never held up by its rim. Where the floor isn’t level and shims are hard to get in, it calls for a 1- to 2-inch bed of mortar. You can read the Sterling bath installation guide yourself; your tub’s own instructions are the ones to follow.
That’s why the old tub coming out is the most important moment of the job. With it gone, we can see the subfloor. If a slow drain leak has softened the wood, it has to be repaired before the new tub goes in. We’ll show you the damage and add the repair to the scope before going further.
How We Install a Fiberglass Tub
- Check the drain location, the opening and the access path before the old tub is removed.
- Remove the old tub and inspect the subfloor and the framing around the alcove.
- Set the new tub level and fully supported, then fasten its flange to the wall studs.
- Install a new waste and overflow and connect it to the drain line.
- Fill the tub, drain it, and check every joint for leaks before any tile or wall panels go back up.
With the walls open, the shower valve is easy to reach. If it’s original or hard to adjust, this is the cheapest time to replace it; our shower valve installation page explains the options. For tubs of other materials, such as acrylic, cast iron or steel, see our main tub installation page. If the tub is part of a bigger bathroom update, read about remodel plumbing and how to plan it.
Swapping a tub in the same spot, with the drain left where it is, normally needs no permit. Moving the drain or changing the layout brings in permit requirements.
Our founder Tony Misleh, master plumber, has run the company since day one in 2007; it holds license CSLB #910268. To have a fiberglass tub looked at or replaced, call (858) 567-0544 during the week. If you write to us through Contact Us, mention whether the leak shows on a ceiling below.
Contact Us
For Same-Day
Water Heater Service,
Call Us On
(858) 567-0544
Check Out Our Ratings!