Slab Leak Repair in San Diego

Concrete slab opened to reach and repair pipes under a San Diego home

A slab leak is a leak in a water pipe that runs under the concrete floor of the house. You can’t see it, so it shows up as clues: a warm patch of floor, a water meter that keeps moving, the sound of water with every tap closed. Courtesy Plumbing does slab leak repair in San Diego on weekdays, 8 AM to 5 PM. There are three ways to fix one, and the right choice depends on the pipe, not only on the leak. This page walks through the tests, the options and how we choose.

Two Tests You Can Run Before You Call

Both take a few minutes and tell us a lot before we arrive.

  1. The meter test. Turn off every faucet and every appliance that uses water, then look at the water meter. The EPA’s version of this check is to read the meter, use no water for two hours, and read it again. If the reading changed, water is leaving the system somewhere.
  2. The hot or cold test. If the meter is moving, close the cold water valve on top of the water heater and look again. If the meter stops, the leak is on the hot side. If it keeps moving, it’s on the cold side or in the line from the meter to the house.

Rule out the toilets too, since a leaking flapper also moves the meter. Put a few drops of food coloring in each tank. Color in the bowl after 10 minutes means that toilet is leaking.

Signs That Point to a Leak Under the Slab

  • A warm spot on a tile or wood floor, which usually means a hot water line.
  • The water heater running far more than it used to, because it’s heating water that never reaches a faucet.
  • A hissing or rushing sound in the walls or floor when nothing is on.
  • Damp carpet, lifting flooring or a musty smell with no fixture nearby.
  • A water bill that climbs with no change in how you use water.

A hot water slab leak costs you twice, once for the water and again for the gas or electricity that heated it. That’s a good reason not to wait on it.

Finding the Spot

Before any concrete is touched, the leak has to be pinned down. We isolate the hot and cold sides, pressure test the lines, and listen along the floor and at the fixtures for the sound of water escaping under pressure. A trained ear picks up more than you’d expect. On one job, our plumber could hear a pinhole leak before the wall was opened, and he cut in right at the spot. The same care applies under a slab, where every extra square foot of opened floor is flooring and concrete someone has to put back.

Three Ways to Repair a Slab Leak

Method

What happens

Fits best when

Keep in mind

Spot repair

The floor is opened at the leak, the bad section of pipe is cut out and replaced, and the concrete is patched.

The pipe is in good shape overall and the leak is easy to reach.

Flooring over that spot has to be removed and replaced. The old pipe on each side stays in service.

Reroute

The leaking line under the slab is cut off and abandoned. A new line is run through the walls or attic to the same fixtures.

The leak sits under a kitchen, tile or hardwood, or that line has leaked before.

No concrete is broken. A few openings in drywall are needed where the new pipe drops to each fixture.

Repipe

All the water lines under the slab are taken out of service and the house gets new piping overhead.

There has been more than one slab leak, or the pipe is worn throughout.

The largest job of the three, and the one that ends slab leaks for good.

Why not always patch the spot? Part of the answer is in the plumbing code. California requires copper tubing under a slab to run without joints wherever possible, and any joint that is allowed has to be brazed, using wrought copper fittings. A spot repair puts new joints under the floor by definition. Done correctly it holds, but it tells you nothing about the next ten feet of the same pipe.

That’s why a reroute is often the better value. We replaced a water heater for one customer and then found a hot water slab leak. We rerouted that line through the attic in a single day, with a few openings in the wallboard and no broken concrete.

When a house has its second or third slab leak, the pipe is telling you something. One long-time customer chose a full repipe after a slab leak for exactly that reason. Our repipe page explains what that job involves and how water stays on in part of the house while it’s done.

How We Choose With You

Four questions decide it:

  • Is it the first leak? A first leak in sound pipe is a candidate for a spot repair or a single reroute.
  • Hot or cold? Hot lines under a slab tend to fail first, and a hot line reroute through the attic is often the simpler job.
  • What’s above it? Breaking through a plain garage floor is very different from breaking through a finished kitchen.
  • What’s the water pressure? Pressure above 80 psi is hard on every pipe in the house. We check it on a slab leak call, because replacing a failed regulator is a far smaller job than a second leak. See our pressure regulator repair page.

You’ll get the options with a price for each before any work starts, including the one we’d pick for our own house and why.

Permits and Drying Out

Stopping a leak is a repair. Replacing a run of pipe with new material, as a reroute or a repipe does, is work the City of San Diego requires a plumbing permit for. We handle the permit and the inspection as part of the job.

Water that has been under flooring for weeks doesn’t dry on its own schedule. If carpet pad, baseboards or drywall are wet, they need proper drying so mold doesn’t follow the leak. Our slab leak water damage restoration page covers that side.

While You Wait for the Repair

  • If the leak is on the hot side, close the cold water valve at the water heater when you don’t need hot water. That stops the flow to the leak.
  • If it’s on the cold side, shut the main valve at the house whenever you leave and overnight.
  • Keep an eye on the meter. A leak that speeds up needs attention sooner.

The EPA estimates that an average household’s leaks waste more than 9,300 gallons of water a year, and its Fix a Leak Week guide has more ways to check a house. A slab leak can waste that much far faster.

If your meter is moving and you can’t find the reason, call (858) 567-0544 on a weekday between 8 AM and 5 PM. Or write down what your two tests showed and send it through Contact Us. We hold California contractor license CSLB #910268, and our founder, Tony Misleh, is a master plumber who has run the company from its start in 2007.

Contact Us

    For Same-Day
    Water Heater Service,
    Call Us On

    (858) 567-0544

    Check Out Our Ratings!